How do I read my Smart Meter?

How to have an Electricity, Economy 7 or Gas Smart Meter reading

 SMETS2 meters will only have an 'A' and 'B' button.

SMETS1 meters will comprise a numeric pad ranging from 1-9.

Electricity Smart Meters

To notice your electricity read you're looking for a number followed by "KWH" but recollect to ignore the numbers later the decimal place.

If you lot accept a keypad

To get a reading from these smart meters:

    1. Printing nine on the keypad.
    2. A series of letters volition appear: IMP KWH.
    3. Then you'll run across eight digits (e.k. 0012565.3) followed by kWh at the bottom correct of the screen.
    4. This is your read, so in this case your reading would be 12565.

If you take an Economy vii smart meter (your meter records 24-hour interval and night usage):

    1. Press vi on the keypad until you run into 'IMP R01' followed by 8 digits - this is unremarkably your dark/off-peak reading.
    2. Then keep on pressing 6 on the keypad until you encounter 'IMP R02' followed by eight digits - this is usually your peak/normal reading.
    3. Ignore whatever digits after a decimal point if you accept one. We but crave the whole numbers.

If you have two buttons

To get a reading from these smart meters:

  1. Press the "Display" or "Brandish Select" push.
  2. By pressing the button the meter display volition scroll through to the meter reading. The number you're afterward is the one followed by kWh.
  3. Every bit earlier write down all the digits, ignoring whatsoever digits later on a decimal point if you have one. We merely require the whole numbers.
  4. In this example the meter reading is 23541.

If yous accept A and B buttons

To become a reading from these smart meters:

  1. Press the A button.
  2. Continue on pressing this until you become to Full Act IMPORT.
  3. The number shown below this is your meter reading.
  4. Ignore any digits after a decimal point if you have one. We only require the whole numbers.
  5. In this example the meter reading is 11256.

If you have iii buttons

To get a reading from these smart meters:

  1. Press the center button.
  2. The number shown below IMP is your meter reading.
  3. If you lot have a 2-rate meter, R1 indicates Charge per unit 1, R2 is Rate 2 and T is total.
  4. You can press the middle button again to run into all the readings.
  5. Ignore any digits after a decimal point if you have i. We only require the whole numbers.
  6. In this example the meter reading is 23541.

If y'all have an orange push on the left and blue buttons on the right

To go a reading from these smart meters:

  1. Press the orange button.
  2. You'll see a row of digits followed by kWh.
  3. Ignore any digits afterward a decimal signal if you lot accept one. Nosotros merely require the whole numbers.
  4. The reading in this example is 12565.

Gas smart meters

To find your gas read you're looking for the number followed past "M3" but call back to ignore the numbers subsequently the decimal place.

If you lot have a keypad

To get a reading from these smart meters:

  1. Press ix on the keypad.
  2. Volume volition appear on the screen.
  3. And then yous'll run across a row of digits (e.g. 00063.5) followed by M3 at the bottom correct of the screen.
    Ignore any digits afterward a decimal betoken if you accept one. We simply require the whole numbers.
  4. The read in this example is 00063.

If you have A and B buttons

To get a reading from these smart meters:

  1. Press the A push button.
  2. Go along on pressing this until you get to METER INDEX.
  3. The number shown beneath this is your meter reading.
  4. Ignore any digits afterward a decimal point if you have one. Nosotros only crave the whole numbers.
  5. In this example the meter reading is 63.

If you lot have a left pointer, a circumvolve and a correct arrow

To get a reading from these smart meters:

  1. Press the centre 'circle' button.
  2. The screen will show 'current meter reading' written along the elevation.
  3. You'll see a row of digits followed past m3.
  4. Ignore any digits after a decimal signal if you have one. We merely require the whole numbers.
  5. The read in this example is 63.

If y'all have 3 square blood-red buttons

or

Your buttons may or may non be labelled A, B and C. To get a reading from these smart meters:

  1. Press the 'A' or left button.
  2. You lot'll come across a row of digits followed by m3.
  3. Ignore whatsoever digits after a decimal point if you accept ane. We only require the whole numbers.
  4. The read in this case is 135.

If you have an orange and a blue pointer to the right of the screen

To become a reading from these smart meters:

  • Press the orangish push.
  • You'll see a row of digits followed past m3.
  • Ignore whatever digits later a decimal point if you have one. We simply crave the whole numbers.
  • In this example the meter reading is 135.

If y'all have two white buttons to the right of your display

Your buttons might have arrows and other markings effectually them.

To get a reading from these smart meters:

  1. Press the right push. This might be labelled 'OK'.
  2. The display should wake upwards and you'll see a row of digits followed by m3.
  3. Ignore any digits subsequently a decimal point if yous have one. We simply require the whole numbers.
  4. In this example the meter reading is 135.

Keywords

Economy vii ; Smart Meter ; reading ; Gas and Electricity Meter Reading

Height 5 frequently asked questions